Kia Picanto: Emergency Call System / Emergency Call (eCall) Unit
Components and components location
The eCall unit for AVN is equipped in AVN head unit. |
Repair procedures
Carry out the Test Mode in the following cases. | –
| Replacing the eCall unit |
| –
| Replacing the Back-up Battery (BUB) |
| –
| Replacing the eCall speaker and MIC |
| –
| Replacing the eCall antenna and roof antenna |
|
| •
| Be careful not to scratch the cluster fascia panel and related parts. |
| •
| When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. |
| •
| Carefully store and handle the crash pad when removing/installing as lubricant and oil can leave a stain on the trim. |
|
eCall Unit
| 1. | Disconnect the negative (-) battery terminal. |
| 2. | Remove the audio unit or AVN head unit.
(Refer to Audio - "Audio Unit")
(Refer to AVN System - "AVN(Audio Video Navigation) Head Unit")
|
| 3. | Disconnect the eCall unit connectors (A).
 |
| 4. | Remove the eCall unit (A) after loosening the mounting bolt and nuts.
 |
eCall Antenna
| 1. | Disconnect the negative (-) battery terminal. |
| 2. | Remove the instrument cluster.
(Refer to Indicators And Gauges - "Instrument Cluster")
|
| 3. | Disconnect the eCall antenna connector (A). |
| 4. | Remove the eCall antenna (B) after loosening the mounting nuts (C).
 |
eCall Speaker
| 1. | Disconnect the negative (-) battery terminal. |
| 2. | Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
|
| 3. | Disconnect the eCall speaker connector (A).
 |
| 4. | Remove the eCall speaker (A) after loosening the mounting nuts.
 |
eCall Unit Back Up Battery (BUB)
| 1. | Disconnect the negative (-) battery terminal. |
| 3. | To replace the back-up battery, remove it after removing the back-up battery cover (A).
 |
Carry out the Test Mode in the following cases. | –
| Replacing the eCall unit |
| –
| Replacing the Back-up Battery (BUB) |
| –
| Replacing the eCall speaker and MIC |
| –
| Replacing the eCall antenna and roof antenna |
|
eCall Unit
| 1. | Install the eCall unit. |
| 2. | Connect the eCall unit connectors. |
| 3. | Install the audio unit or AVN head unit. |
| 4. | Connect the negative (-) battery terminal. |
eCall Antenna
| 1. | Install the eCall antenna. |
| 2. | Connect the eCall antenna connector. |
| 3. | Install the instrument cluster. |
| 4. | Connect the negative (-) battery terminal. |
eCall Speaker
| 1. | Install the eCall speaker. |
| 2. | Connect the eCall speaker connector. |
| 3. | Install the crash pad lower panel. |
| 4. | Connect the negative (-) battery terminal. |
Inspection (With KDS/GDS)
| 1. | In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (KDS/GDS). The diagnostic system (KDS/GDS) provides the following information. | (1) | Self diagnosis : Checks failure and code number (DTC) |
| (2) | Current data : Checks the system input/output data state |
| (3) | Actuation test : Checks the system operating condition |
| (4) | Additional function : Controls other features including system option setting and zero point adjustment |
|
| 2. | Select the 'Car model' and the 'Telematics System' to be checked in order to check the vehicle with the tester. |
| 3. | Select the 'Current Data' menu to check the current state of the input/output data. |
eCall Test Mode
Press the SOS TEST button to activate the audio guidance and test the eCall system according to the guidance.
In
the Test Call stage, which is the last stage of the test mode, press
the SOS button according to the audio guidance to send the data on
faulty components to the call center.
To stop the test mode, press the SOS TEST button again during the audio guidance.
| 1. | Conditions for the test mode operation | (1) | Vehicle battery is connected properly. |
| (2) | One minute has passed after ignition. |
| (3) | The vehicle remains stationary for 1 minute or more. |
|
| 2. | Conditions preventing the test mode operation | (1) | A call is made to a PSAP |
| (2) | Call
Back mode : The eCall system enters the Call Back mode after a
successful call and is in standby for 120 minutes to receive calls from
the call center. |
| (3) | The test mode automatically ends when the vehicle speed is 1 km/h or above or has moved 300 m or more. |
| (4) | Two minutes have not passed after the previous test call ended. |
|
| 3. | Operation sequence of the test mode (audio guidance) | (4) | BUB (Back-up battery embedded in the eCall unit) test (no separate notification is provided if the BUB is in normal condition.) | •
| Backup battery audio prompt guide If
the audio guidance notifies that "The voltage of Backup battery is low
to make emergency call", retry test mode after sufficiently charging the
battery by driving. |
|
|
| (5) | Test call (Pressing the SOS button sends the test result to a PSAP.) |
|
The red LED stays turned on if one or more DTCs for the eCall system are issued. If the red LED is on, be sure to use the diagnostic tool (KDS/GDS) to check for any failure. |
Inspecting Back-up Battery
Back-up
battery (BUB) embedded in the eCall system has a finite lifespan and
its charging/discharging performance may be diminished after an
extensive use.
The
back-up battery guarantees the operation of the eCall system when the
vehicle battery cannot be used due to an accident. Be sure to inspect
the back-up battery if the red LED turns on and replace it if necessary.
Warranty on Back-up Battery is 3 years. Inspect the back-up battery every three years and replace it if necessary.
(Refer to Emergency Call Unit - "Repair Procedures")
|
The
eCall system is aimed to place an urgent call to the call center during
an emergency. Arbitrarily removing or operating the system components
may affect the safety of people and may result in false notification of
an accident to the emergency call center. |
Components and components location
Components
1. Head unit (AVN, Audio) 2. Emergency call system button 3. Emergency call system MIC 4. Roof antenna 5. Emergency call unit 6. Supplemental Re ...
Components and components location
Component
Repair procedures
Removal
1. Disconnect the negative (-) battery terminal.
2. Using a screwdriver or remover, separate the map lamp ...
Other information:
The rearview camera will activate when
the back-up light is ON with the ignition
switch ON and the shift lever in the R
(Reverse) position.
This system is a supplemental system
that shows behind the vehicle through
the navigation display while backingup.
WARNING
This system is a su ...
Repair procedures
Inspection
1.Ignition "ON"
2.Manually operate the control switch and measure the voltage of blower motor.
3.Select the control switch to raise voltage until high speed.
Fan
Motor Voltage
ManualFirst speed3. ...
Emergency Call System
Emergency Call (eCall) Button